Herstellung von Chitosan und einige Anwendungen

  • 1. Die Deacetylierung von crabshell – Chitosan führte gleichzeitig zu einem drastischen Abfall der mittleren viscosimetrischen Molmasse ( Mv), insbesondere wenn die Temperatur und die Konzentration an NaOH erhöht werden. Diese Parameter beeinflussten jedoch nicht den Grad der Deacetylierung (DD). Wichtig ist jedoch die Quelle des Ausgangsmaterials: Chitin aus Pandalus borealis ist ein guter Rohstoff für die Herstellung von Chitosan mit niedrigem DD und gleichzeitig hoher mittlerer Mv, während Krill-Chitin (Euphausia superba) ein gutes Ausgangsmaterial zur Herstellung von Chitosan mit hohem DD und niedrigem Mv ist. Chitosan, das aus Insekten (Calliphora erythrocephala), unter milden Bedingungen (Temperatur: 100°C, NaOH-Konzentration: 40 %, Zeit: 1-2h ) hergestellt wurde, hatte die gleichen Eigenschaften hinsichtlich DD und Mv wie das aus Krill hergestellte Chitosan. Der Bedarf an Zeit, Energie und NaOH ist für die Herstellung von Insekten-Chitosan geringer als für crabshell-Chitosan vergleichbare Resultaten für DD und Mv. 2. Chitosan1. Die Deacetylierung von crabshell – Chitosan führte gleichzeitig zu einem drastischen Abfall der mittleren viscosimetrischen Molmasse ( Mv), insbesondere wenn die Temperatur und die Konzentration an NaOH erhöht werden. Diese Parameter beeinflussten jedoch nicht den Grad der Deacetylierung (DD). Wichtig ist jedoch die Quelle des Ausgangsmaterials: Chitin aus Pandalus borealis ist ein guter Rohstoff für die Herstellung von Chitosan mit niedrigem DD und gleichzeitig hoher mittlerer Mv, während Krill-Chitin (Euphausia superba) ein gutes Ausgangsmaterial zur Herstellung von Chitosan mit hohem DD und niedrigem Mv ist. Chitosan, das aus Insekten (Calliphora erythrocephala), unter milden Bedingungen (Temperatur: 100°C, NaOH-Konzentration: 40 %, Zeit: 1-2h ) hergestellt wurde, hatte die gleichen Eigenschaften hinsichtlich DD und Mv wie das aus Krill hergestellte Chitosan. Der Bedarf an Zeit, Energie und NaOH ist für die Herstellung von Insekten-Chitosan geringer als für crabshell-Chitosan vergleichbare Resultaten für DD und Mv. 2. Chitosan wurde durch den Schimmelpilz Aspergillus fumigatus zu Chitooligomeren fermentiert. Die Ausbeute beträgt 25%. Die Chitooligomere wurden mit Hilfe von HPLC und MALDI-TOF-Massenspektrmetrie identifiziert. Die Fermentationsmischung fördert die Immunität von Pflanzen gegen Bakterien und Virusinfektion. Die Zunahme der Immunität schwankt jedoch je nach System Pflanze-Pathogen. Die Fermentation von Chitosan durch Aspergillus fumigatus könnte eine schnelle und billige Methode zur Herstellung von Chitooligomeren mit guter Reinheit und Ausbeute sein. Eine partiell aufgereinigte Fermentationsmischung dieser Art könnte in der Landwirtschaft als Pathogeninhibitor genutzt werden. Durch kontrollierte Fermentation, die Chitooligomere in definierter Zusammensetzung (d.h. definierter Verteilung des Depolymerisationsgrades) liefert, könnte man zu Mischungen kommen, die für die jeweilige Anwendung eine optimale Bioaktivität besitzen. 3. Die aus Chitosan-Dispersionen hergestellten MCChB-Filme weisen bessere mechanische Eigenschaften (Bruchfestigkeit, Dehnung) und eine höhere Wasseraufnahmefähigkeit auf als Filme, die nach herkömmlichen Methoden aus sauerer Lösung hergestellt werden. Die Einführung von Proteinen ändert die mechanischen Eigenschaften der MCChB-Filme abhängig von der Art, der Proteine sowie des DD und der Mv des eingesetzte Chitosan. Die Zugabe von Protein beschleunigt den biologischen Abbau der MCChB-Filme. Aus den untersuchten MCChB-Filmen mit Proteinzusatz können leichte, reißfeste und dennoch elastische Materialen hergestellt werden. 4. Mit Hilfe von MCChB-Dispersion kann Papier modifiziert werden. Dadurch werden die mechanischen Eigenschaften verbessert und die Wasseraufnahme wird verringert. Die Zugabe von Proteinen verringert das Wasseraufnahmevermögen noch weiter. Ein geringes Wasseraufnahmevermögen ist der bedeutendste Faktor bei der Papierherstellung. Auch Papier, das mit einem MCChB-Protein-Komplexe modifiziert wurde, zeigt gute mechanische Eigenschaften. 5. Wird Chitosan durch unmittelbare Einführung von MCChB auf Cellulose-Fasern aufgebracht, so erhält man eine netzartige Struktur, während durch Ausfällung aufgebrachtes Chitosan eine dünne Schicht auf den Cellulose-Fasern bildet. Die netzartige Struktur erleichtert die Bioabbaubarkeit, während die Schichtstruktur diese erschwert. 6. Die guten mechanischen Eigenschaften, die geringe Wasseraufnahmefähigkeit und die mit Cellulose vergleichbare Bioabbaubarkeit von Papier, das mit MCChB modifiziert wurde, lassen MCChB für die Veredlung von Papier nützlich erscheinen.show moreshow less
  • 1. Deacetylation of the crustacean chitosan causes drastically decrease in the Mv with increasing reaction temperature and time as well as the concentration of sodium hydroxide. However, the DD are relatively less affected. Pandalus borealis is a good source for production of chitosan having high Mv and low DD, whereas chitosan of medium to low Mv can ideally be prepared using krill chitin. Insect chitosan is prepared under milder condition as compared with the crustacean chitosan, showed similar Mv and DD. Moreover, the consumption of time, energy and sodium hydroxide is much lower than for crustacean chitosan used. The properties of chitin (type of source, crystallinity, DD, Mv, swelling properties, particle size) affect the deacetylated polymer parameters. 2. Fermentation of chitosan using fungus Aspergillus fumigatus resulted in a composition of oligosaccharides with controlled molecular weight and yield at least 25 wt%. The product of fermentation effectively inhibited the viral and/or bacterial infection of the plant. This1. Deacetylation of the crustacean chitosan causes drastically decrease in the Mv with increasing reaction temperature and time as well as the concentration of sodium hydroxide. However, the DD are relatively less affected. Pandalus borealis is a good source for production of chitosan having high Mv and low DD, whereas chitosan of medium to low Mv can ideally be prepared using krill chitin. Insect chitosan is prepared under milder condition as compared with the crustacean chitosan, showed similar Mv and DD. Moreover, the consumption of time, energy and sodium hydroxide is much lower than for crustacean chitosan used. The properties of chitin (type of source, crystallinity, DD, Mv, swelling properties, particle size) affect the deacetylated polymer parameters. 2. Fermentation of chitosan using fungus Aspergillus fumigatus resulted in a composition of oligosaccharides with controlled molecular weight and yield at least 25 wt%. The product of fermentation effectively inhibited the viral and/or bacterial infection of the plant. This method can be an excellent, inexpensive system for preparation of bioactive agent. The preliminary purified fermentation mixture due to its antiviral and antibacterial behaviour is capable to be used as a natural, plant protection agent. The controlled degradation of chitosan connected with the production of various oligosaccharides having specified molecular weight allows obtaining the product with optimum bioactivity for suitable applications. 3. The films formed form microcrystalline chitosan (MCChB) gel-like dispersion demonstrate the better mechanical properties and higher swelling behaviour than typical films prepared using acidic solution of chitosan. The introduction of proteins significantly changes the mechanical strength and swelling behaviour. Addition of proteins causes the increase in their biodecomposition. The blended films containing proteins could be the base for formation of the resistant materials showed excellent elongation at break. 4. The application of MCChB in a paper formation as a modificator of the fibre-water interactions allows producing the paper sheets indicating the high increase in the mechanical properties and significant decrease in swelling properties. The introduction of MCChB with proteins causes a slight decrease in paper mechanical strength, if determined at low relative humidity. However, the mechanical strength measured at high relative humidity differ less than for paper sheet containing only MCChB. 5. Direct introduction of MCChB to a paper pulp forms the "web-like" structure of cellulose fibres and MCChB. The "web-like" structure of MCChB enables the faster biodecomposition of formed paper sheets. The precipitation of MCChB as wells as introduction of MCChB with proteins causes the "coat-like" structure. MCChB creates a thin layers coated the cellulose fibres lowering a biodecomposition rate. 6. The properties of paper sheets modified by MCChB such as: similar to cellulose biodegradation, excellent mechanical properties at rel. high humidity and the decrease in swelling properties as well as various possibilities to introduce MCChB allow to apple microcrystalline chitosan with or without proteins as the modificator of the fibre-water interactions in paper.show moreshow less

Download full text files

Export metadata

Additional Services

Search Google Scholar Statistics
Metadaten
Author details:Marcin Henryk Struszczyk
URN:urn:nbn:de:kobv:517-0000319
Supervisor(s):Joachim Koetz, Stefan Boryniec, Martin G. Peter
Publication type:Doctoral Thesis
Language:German
Publication year:2000
Publishing institution:Universität Potsdam
Granting institution:Universität Potsdam
Date of final exam:2001/05/01
Release date:2005/02/07
GND Keyword:Chitosan / Präparative Chemie / Verpackungsmaterial / Mikrobielle Abbaubarkeit / Chitosan / Proteine
RVK - Regensburg classification:VK 5070
Organizational units:Mathematisch-Naturwissenschaftliche Fakultät / Institut für Chemie
DDC classification:5 Naturwissenschaften und Mathematik / 54 Chemie / 540 Chemie und zugeordnete Wissenschaften
Accept ✔
This website uses technically necessary session cookies. By continuing to use the website, you agree to this. You can find our privacy policy here.